Sears International Online Shopping If you are planning to visit the United States, or have friends and family here, shop at Sears to get everything you want—including gifts for yourself or others. Shopping online in the U.S. At Sears could not be easier.

You can pay for your order in a store or even use an international credit card. Once you place an order, you (or someone you know) can pick it up at a Sears store, have it shipped to over 100 countries—whatever is most convenient for you. If you are looking to do some international online shopping, be sure to visit.

You've just moved into your new home, the new drapes are up, and the washer and dryer are ready to be put into place. The dryer cord won't plug in—the dryer cord has four prongs, but the wall receptacle only has three holes! What's up with this? What's up is that in 1999 the National Electric Code instituted a change, requiring all new dryers and home dryer receptacles to have 4 prongs instead of the older 3-prong style. That fourth prong is a ground wire and is there for better electrical safety. Now, it would be convenient if there was a dryer plug adapter that you could plug into that three-pronged receptacle so that you could plug your dryer into that—but there isn't.

You will have to change the dryer cord to make it fit. The good news is that dryer cords are readily available and fairly inexpensive, and it isn’t very hard to switch them. A screwdriver and a pair of pliers will do the job, although some nut drivers would be nice. Now if the situation with your dryer cord and outlet is backwards from this—that is, you have a three-pronged cord and a four-pronged outlet—you are looking at the wrong article. Look at this article instead:.

Allowing some slack in the cord. Refer to the pre-installation requirements in. This dryer is equipped with a three-prong. Your dryer needs the space. How to change power cord on kenmore HE3 elite electric dryer? Before disconnecting the existing 3 prong plug. Pdf Mit Bildern Verkleinern. How to reverse dryer door on kenmore elite HE3.

Begin by unplugging the dryer. There is high voltage inside (240 volts) that can give you a very nasty shock, even kill you. Make sure there is no chance of this, by unplugging the dryer before proceeding any further. There will be some kind of connector holding the dryer cable to the wall of the dryer so that it doesn't pull out. The most common type is a clamp with two screws on the outside that can be tightened to squeeze the wire into place. Loosen these screws so that the wire can slide out of the dryer. Remove the cover plate from the wire terminal block, exposing the wires inside.

Note where each color of wire terminates. Normally, you will see a row of three terminal screws, with the red and black wires connected to the two outside screws, the white wire connected to the center screw, and the green wire connected to the frame of the dryer. Once the four-wire cord is removed, it is time to install the new three-wire cord and plug. Work the wire through the connector, but do not tighten it yet. The red and black wires go to the outer two terminals (in the photo the dryer wires are black and blue) and the white wire goes to the terminal in the center of the terminal block. Install Alsa Drivers Ubuntu 12.04.

While the red and black wires are interchangeable, the white wire is not; make sure it goes to the center terminal, where the old white wire was. Most three-wire cords do not have colored wires, so instead of matching colors, identify the wires using the relative position of the wires in the cord. The center wire of the three will always go to the center (white) terminal; the outer two wires go to the outer terminals. The outer two wires can be interchanged, but never put the center wire of a flat, three-wire cord on anything but the center terminal. Your three-prong cord will not have a green ground wire. In place of that wire a ground strap or short piece of #10 wire (preferably green) must be installed.

One end should go to where the green wire on the old cord went, and the other end to the terminal where the white wire went. Do not ignore this step! You must have a 'jumper' of some kind, a wire or strap, installed between the dryer frame and the white wire. This jumper is the only thing that grounds the dryer. Without it, if there is an electrical problem later, the frame may become energized and present a huge shock hazard. Robokill Titan Prime Full Version on this page. The photo shows a metal strap installed; it goes from the white wire down the side of the terminal block, and is screwed to the dryer frame. If this strap is not available (and it usually isn't) purchase a one-foot piece of #10 green wire, strip an inch of insulation from each end, and install that wire between the connector the white wire used to go to and the connector on the frame where the green wire used to go.